Posts tagged plc siemens programming

siemens simatic s7 plc 6EP1332-1SH71 POWER SUPPLY S7-1200 PM1207

plc siemens simatic s7 SIMATIC S7-1200 POWER MODULE PM1207 STABILIZED POWER SUPPLY INPUT: 120/230 V AC OUTPUT: 24 V DC/2.5 A

Technical specifications
Product S7-1200 PM1207
Power supply, type 24 V/2.5 A
Input
Input 1-phase AC
Supply voltage / 1 / at AC / nominal value 120 V
Supply voltage / 2 / at AC / nominal value 230 V
Voltage range
  • Note
Automatic range selection
Input voltage / 1 / at AC 85…132 V
Input voltage / 2 / at AC 176…264 V
Wide-range input No
Overvoltage resistance 2.3 × Vin rated, 1.3 ms
Mains buffering at Iout rated, min. 20 ms
Mains buffering at Vin = 93/187 V
Rated line frequency 50/60 Hz
Rated line range 47…63 Hz
Input current / at nominal level of the input voltage 120 V 1.2 A
Input current / at nominal level of the input voltage 230 V 0.67 A
Switch-on current limiting (+25 °C), max. 13 A
Duration of current limiting / at 25 °C / maximum 3 ms
I²t, max. 0.5 A²·s
Built-in incoming fuse T 3,15 A/250 V (not accessible)
Protection in the mains power input (IEC 898) Recommended miniature circuit breaker: 16 A, characteristic B, or 10 A, characteristic C
Output
Output Controlled, isolated DC voltage
Rated voltage Vout DC 24 V
Total tolerance, static ± 3 %
Static mains compensation, approx. 0.1 %
Static load balancing, approx. 0.2 %
Residual ripple peak-peak, max. 150 mV
Spikes peak-peak, max. (bandwidth: 20 MHz) 240 mV
Product feature / output voltage adjustable No
Output voltage setting -
Status display Green LED for 24 V OK
On/off behavior No overshoot of Vout (soft start)
Startup delay, max. 6 s
  • Note
2 s at 230 V, 6 s at 120 V
Voltage rise, typ. 10 ms
Rated current value Iout rated 2.5 A
Current range 0…2.5 A
delivered active power / typ. 60 W
short-term overload current / at short-circuit during run-up / typical 6 A
Duration of overloading ability for excess current / on short-circuiting during the start-up 100 ms
short-term overload current / at short-circuit during operation / typical 6 A
Duration of overloading ability for excess current / on short-circuiting during the operational phase 100 ms
Parallel switching for enhanced performance Yes
Numbers of parallel switchable units for enhanced performance 2
Efficiency
Efficiency at Vout rated, Iout rated, approx. 83 %
Power loss at Vout rated, Iout rated, approx. 12 W
Closed-loop control
Dynamic mains compensation (Vin rated ±15 %), max. 0.3 %
Dynamic load smoothing (Iout: 50/100/50 %), Uout ± typ. 3 %
Load step setting time 50 to 100%, typ. 5 ms
Load step setting time 100 to 50%, typ. 5 ms
Setting time / maximum 5 ms
Protection and monitoring
Output overvoltage protection < 33 V
Current limitation, typ. 2.65 A
Characteristic feature of the output / short-circuit protected Yes
Short-circuit protection Constant current characteristic
Enduring short circuit current / Effective level / typical 2.7 A
Overload/short-circuit indicator -
Safety
Primary/secondary isolation Yes
Potential separation Safety extra-low output voltage Uout acc. to EN 60950-1 and EN 50178
Protection class Class I
stray current / maximum 3.5 mA
CE mark Yes
UL/CSA approval Yes
UL/cUL (CSA) approval cULus-Listed (UL 508, CSA C22.2 No. 107.1), File E197259; cURus-Recognized (UL 60950-1, CSA C22.2 No. 60950-1) File E151273
Explosion protection ATEX (EX) II 3G Ex nA II T4; cULus (ISA 12.12.01, CSA C22.2 No.213) File E330455
FM approval Class I, Div. 2, Group ABCD, T4
CB approval No
Marine approval GL, ABS, BV, DNV, LRS, NK
Degree of protection (EN 60529) IP20
EMC
Emitted interference EN 55022 Class B
Supply harmonics limitation not applicable
Noise immunity EN 61000-6-2
Operating data
Ambient temperature / in operation 0…60 °C
  • Note
with natural convection
Ambient temperature / on transport -40…+85 °C
Ambient temperature / in storage -40…+85 °C
Humidity class according to EN 60721 Climate class 3K3, no condensation
Mechanics
Connection technology screw-type terminals
Connections / Supply input L, N, PE: 1 screw terminal each for 0.5 … 2.5 mm²
Connections / Output L+, M: 2 screw terminals each for 0.5 … 2.5 mm²
Connections / Auxiliary -
Width / of the housing 70 mm
Height / of the housing 100 mm
Depth / of the housing 75 mm
Installation width 70 mm
Mounting height 140 mm
Weight, approx. 0.3 kg
Product feature / of the housing / housing for side-by-side mounting Yes
Type of mounting / wall mounting Yes
Type of fixing / cap rail mounting Yes
Type of mounting / S7-300 rail mounting No
Installation Snaps onto DIN rail EN 60715 35×7.5/15, wall mounting
Other information Specifications at rated input voltage and ambient temperature +25 °C (unless otherwise specified)