Archive for the Other siemens plc hardware Category

siemens plc simatic 6GK7277-1AA10-0AA0 COMPACT SWITCH MODULE CSM 1277

sps programmierung s7 COMPACT SWITCH MODULE CSM 1277 CONNECTION SIMATIC S7-1200 AND UP TO 3 FURTHER IND. ETHERNET USERS WITH 10/100 MBIT/S UNMANAGED SWITCH, 4 RJ45 PORTS, EXT. 24V DC POWER SUPPLY, LED DIAGNOSTICS, S7-1200 MODULE INCL. ELECTRONIC MANUAL ON CD

Transmission rate
Transfer rate / 1 10 Mbit/s
Transfer rate / 2 100 Mbit/s
Interfaces
Number of electrical/optical connections / for network components or terminal equipment / maximum 4
Number of electrical connections
  • for network components and terminal equipment
4
  • for power supply
1
Design of the electrical connection
  • for network components and terminal equipment
RJ45 port
  • for power supply
3-pole terminal block
Supply voltage, current consumption, power loss
Type of voltage / of supply voltage DC
Supply voltage / external 24 V
  • minimum
19.2 V
  • maximum
28.8 V
Product component / fusing at power supply input Yes
Type of fusing / at input for supply voltage 0,5 A / 60 V
Consumed current / maximum 0.07 A
Active power loss / at 24 V / for DC 1.6 W
Permitted ambient conditions
Ambient temperature
  • during operating
0…60 °C
  • during storage
-40…+70 °C
  • during transport
-40…+70 °C
Relative humidity
  • at 25 °C / without condensation / during operating / maximum
95 %
Protection class IP IP20
Design, dimensions and weight
Design SIMATIC S7-1200 device design
Width 45 mm
Height 100 mm
Depth 75 mm
Net weight 0.15 kg
Type of mounting
  • 35 mm DIN rail mounting
Yes
  • wall mounting
Yes
  • S7-300 rail mounting
No
Product properties, functions, components / general
Product function / switch-managed No
Standard
  • for EMC / from FM
FM3611: Class 1, Division 2, Group A, B, C, D / T.., CL.1, Zone 2, GP. IIC, T.. Ta
  • for hazardous zone
EN 600079-15:2005, EN 600079-0:2006, II 3 G Ex nA II T4, KEMA 08 ATEX 0003 X
  • for safety / of CSA and UL
UL 508, CSA C22.2 No. 142
  • for emitted interference
EN 61000-6-4 (Class A)
  • for interference immunity
EN 61000-6-2
Verification of suitability EN 61000-6-2, EN 61000-6-4
  • CE mark
Yes
  • C-Tick
Yes
  • KC approval
No

 

siemens plc hardware 6ES7297-0AX30-0XA0 BATTERY BOARD BB 1297 F. CPU 12XX

automation plc programming SIMATIC S7-1200, BATTERY BOARD BB 1297 FOR LONG-TERM BACKUP OF THE REALTIME CLOCK; PLUGGABLE IN THE SIGNAL BOARD S7-12XX CPU (FW3.0 AND LATER); BATTERY (CR1025) NOT INCLUDED

Interrupts/diagnostics/status information
Alarms
Alarms Yes
Diagnostic messages
Diagnostic functions Yes
Diagnostics indication LED
for maintenance Yes; The maintenance LED (MAINT) of the PLC signals that the battery needs to be replaced.
Degree and class of protection
IP20 Yes
Standards, approvals, certificates
CE mark Yes
CSA approval Yes
C-TICK Yes
FM approval Yes
Marine approval Yes
Marine approval according to American Bureau of Shipping Yes
Marine approval according to Bureau Veritas Yes
Marine approval according to Det Norske Veritas Yes
Marine approval according to Germanischer Lloyd Yes
Marine approval according to Lloyds Register of Shipping Yes
Climatic and mechanical conditions for storage and transport
Climatic conditions for storage and transport
Free fall
Drop height, max. (in packaging) 0.3 m; five times, in dispatch package
Temperature
Permissible temperature range -40 °C to +70 °C
Air pressure acc. to IEC 60068-2-13
Permissible air pressure 1080 to 660 hPa
Mechanical and climatic conditions during operation
Climatic conditions in operation
Temperature
Min. -20 °C
max. 60 °C
Air pressure acc. to IEC 60068-2-13
Permissible air pressure 1080 to 795 hPa
Mechanics/material
Type of housing (front)
Plastic Yes
Dimensions
Width 38 mm
Height 62 mm
Depth 21 mm
Weights
Weight, approx. 40 g

siemens s7 plcs 6ES7290-6AA30-0XA0 SIMATIC S7-1200, EXPANSION CABLE 2.0M

siemens simatic s7 plc SIMATIC S7-1200, EXPANSION CABLE TWO-ROW ARRANGEMENT FOR SM 12XX, 2.0 M

siemens simatic s7 plc 6EP1332-1SH71 POWER SUPPLY S7-1200 PM1207

plc siemens simatic s7 SIMATIC S7-1200 POWER MODULE PM1207 STABILIZED POWER SUPPLY INPUT: 120/230 V AC OUTPUT: 24 V DC/2.5 A

Technical specifications
Product S7-1200 PM1207
Power supply, type 24 V/2.5 A
Input
Input 1-phase AC
Supply voltage / 1 / at AC / nominal value 120 V
Supply voltage / 2 / at AC / nominal value 230 V
Voltage range
  • Note
Automatic range selection
Input voltage / 1 / at AC 85…132 V
Input voltage / 2 / at AC 176…264 V
Wide-range input No
Overvoltage resistance 2.3 × Vin rated, 1.3 ms
Mains buffering at Iout rated, min. 20 ms
Mains buffering at Vin = 93/187 V
Rated line frequency 50/60 Hz
Rated line range 47…63 Hz
Input current / at nominal level of the input voltage 120 V 1.2 A
Input current / at nominal level of the input voltage 230 V 0.67 A
Switch-on current limiting (+25 °C), max. 13 A
Duration of current limiting / at 25 °C / maximum 3 ms
I²t, max. 0.5 A²·s
Built-in incoming fuse T 3,15 A/250 V (not accessible)
Protection in the mains power input (IEC 898) Recommended miniature circuit breaker: 16 A, characteristic B, or 10 A, characteristic C
Output
Output Controlled, isolated DC voltage
Rated voltage Vout DC 24 V
Total tolerance, static ± 3 %
Static mains compensation, approx. 0.1 %
Static load balancing, approx. 0.2 %
Residual ripple peak-peak, max. 150 mV
Spikes peak-peak, max. (bandwidth: 20 MHz) 240 mV
Product feature / output voltage adjustable No
Output voltage setting -
Status display Green LED for 24 V OK
On/off behavior No overshoot of Vout (soft start)
Startup delay, max. 6 s
  • Note
2 s at 230 V, 6 s at 120 V
Voltage rise, typ. 10 ms
Rated current value Iout rated 2.5 A
Current range 0…2.5 A
delivered active power / typ. 60 W
short-term overload current / at short-circuit during run-up / typical 6 A
Duration of overloading ability for excess current / on short-circuiting during the start-up 100 ms
short-term overload current / at short-circuit during operation / typical 6 A
Duration of overloading ability for excess current / on short-circuiting during the operational phase 100 ms
Parallel switching for enhanced performance Yes
Numbers of parallel switchable units for enhanced performance 2
Efficiency
Efficiency at Vout rated, Iout rated, approx. 83 %
Power loss at Vout rated, Iout rated, approx. 12 W
Closed-loop control
Dynamic mains compensation (Vin rated ±15 %), max. 0.3 %
Dynamic load smoothing (Iout: 50/100/50 %), Uout ± typ. 3 %
Load step setting time 50 to 100%, typ. 5 ms
Load step setting time 100 to 50%, typ. 5 ms
Setting time / maximum 5 ms
Protection and monitoring
Output overvoltage protection < 33 V
Current limitation, typ. 2.65 A
Characteristic feature of the output / short-circuit protected Yes
Short-circuit protection Constant current characteristic
Enduring short circuit current / Effective level / typical 2.7 A
Overload/short-circuit indicator -
Safety
Primary/secondary isolation Yes
Potential separation Safety extra-low output voltage Uout acc. to EN 60950-1 and EN 50178
Protection class Class I
stray current / maximum 3.5 mA
CE mark Yes
UL/CSA approval Yes
UL/cUL (CSA) approval cULus-Listed (UL 508, CSA C22.2 No. 107.1), File E197259; cURus-Recognized (UL 60950-1, CSA C22.2 No. 60950-1) File E151273
Explosion protection ATEX (EX) II 3G Ex nA II T4; cULus (ISA 12.12.01, CSA C22.2 No.213) File E330455
FM approval Class I, Div. 2, Group ABCD, T4
CB approval No
Marine approval GL, ABS, BV, DNV, LRS, NK
Degree of protection (EN 60529) IP20
EMC
Emitted interference EN 55022 Class B
Supply harmonics limitation not applicable
Noise immunity EN 61000-6-2
Operating data
Ambient temperature / in operation 0…60 °C
  • Note
with natural convection
Ambient temperature / on transport -40…+85 °C
Ambient temperature / in storage -40…+85 °C
Humidity class according to EN 60721 Climate class 3K3, no condensation
Mechanics
Connection technology screw-type terminals
Connections / Supply input L, N, PE: 1 screw terminal each for 0.5 … 2.5 mm²
Connections / Output L+, M: 2 screw terminals each for 0.5 … 2.5 mm²
Connections / Auxiliary -
Width / of the housing 70 mm
Height / of the housing 100 mm
Depth / of the housing 75 mm
Installation width 70 mm
Mounting height 140 mm
Weight, approx. 0.3 kg
Product feature / of the housing / housing for side-by-side mounting Yes
Type of mounting / wall mounting Yes
Type of fixing / cap rail mounting Yes
Type of mounting / S7-300 rail mounting No
Installation Snaps onto DIN rail EN 60715 35×7.5/15, wall mounting
Other information Specifications at rated input voltage and ambient temperature +25 °C (unless otherwise specified)